JJ 239 Trioden Monoblock Röhrenverstärker

High-End, Eintaktverstärker Class A1, Trioden Monoblock, 10 Watt an 4 und 8 Ohm. Mit jeweils einer ECC99 und 2A3-40 JJ Electronic Röhre.

Mehr Infos

  • Ahorn/24 kt Goldbeschichtet
  • Schwarz/Chrom
  • Elfenbein/Chrom

Auf meine Wunschliste

    Mono Blocks JJ 239 use 2A3-40W and ECC99 tubes (similar to Mono Blocks JJ309 which use 300B and ECC99).

    The JJ239 was developed on request from customers from Southeast Asia and Japan after the 2A3-40W tube was introduced. The 2A3-40W showed as having the best sound in the group of power triodes.

    Like the 300B, the 2A3 has perfect linearity due to the design of the internal geometry.

    The sound quality however, is even better because the cathode heater voltage is only 2.5V and the filament ends potential difference with respect to –Ug is smaller than in the 300B tube. Therefore, a much bigger cathode area is active during operation. (The maximum current flows at the positive filament end). Power source filtration capacitance of RC filters is 1200 μF.

    The electrolytic capacitors of JJ Electronic production are bypassed with high quality polypropylene capacitors. Filament voltages for all tubes are of DC type.

    The signal is amplified(in class A) by either of the ECC99. The ECC99 drives 2A3 which has an amplitude swing Uamax = 205V. The output transformer ratio of 31 : 1 / 4 Ohm helps to achieve the damping factor of 3,5.

    The output transformer is a double c-core and its topology is similar to the JJ322.

    All circuits in the signal path are optimized and THD at 9W is less than 1%.

    JJ239 allows the anode current of 2A3-4W to be set using a potentiometer on the back panel. The LED under the potentiometer indicates the correct settting. The current is set correctly if the LED light just comes on.

    A soft-start circuit turns the plate circuitry on with a delay of approximately 30 sec.

Röhrenbestückung 1 x JJ ECC99
1 x JJ 2A3 - 40 W
Ausgangsleistung 10 Watt
Ausgangsimpedanz 4 Ohm/8 Ohm
Eingangsimpedanz 50 kOhm
Eingangsempfindlichkeit 0,775 Volt bei 10 Watt
Frequenzbereich 20 Hz - 20 000 Hz (-1 dB)
Fremdspannungsabstand weniger als 0,8 mV
Ausgangsübertrager Schnittbandkern (Double „C.cores“)
Dämpfungsfaktor 3,5
Stromversorgung 230 V (120 V, 100 V) 50/60 Hz
Leistungsaufnahme 80 Watt
Maße 340 x 380 x 255 mm
Gewicht 23 kg
Finish Trafo Abdeckung: Braun oder Schwarz (Pulverlack)
Deckplatte: Chrome oder 24 Karat Goldbeschichtet
Holz: Braun, Elfenbein (glänzend) oder Schwarz (matt)

Bewertungen

Bisher noch kein Kundenkommentar

Eigene Bewertung verfassen

JJ 239 Trioden Monoblock Röhrenverstärker

JJ 239 Trioden Monoblock Röhrenverstärker

High-End, Eintaktverstärker Class A1, Trioden Monoblock, 10 Watt an 4 und 8 Ohm. Mit jeweils einer ECC99 und 2A3-40 JJ Electronic Röhre.

Eigene Bewertung verfassen

Zubehör